DBAW15BF2-2X/200Z6EG24N9K4
Manufacturer: Bosch Rexroth
Material #: R901118996
Model : DBAW15BF2-2X/200Z6EG24N9K4
***Disclaimer: The following summary contains information gathered from various sources such as product descriptions, technical specifications and catalogs. While efforts have been made to provide accurate details, inaccuracies may occur. It is advised to verify all information by contacting Bosch Rexroth directly.***
The Bosch Rexroth DBAW15BF2-2X/200Z6EG24N9K4 (R901118996) is an advanced pump safety block designed for high-performance hydraulic systems. This product is specifically engineered to be mounted directly onto SAE pressure ports of pumps, providing an efficient solution for limiting the operating pressure and enabling solenoid-actuated unloading. The DBAW15BF2-2X/200Z6EG24N9K4 incorporates a pilot-operated pressure relief valve integrated into a single block, eliminating the need for a separate cover plate due to its unique design that allows for direct control of the main spool via a mounted directional valve.
This model is versatile and can be used in various configurations, including types DBAW.BZ, DBAW.BZA, and DBAW.BZZA, each tailored to different pump control applications. It features a pressure relief valve type ZDB that works in conjunction with the directional valve to adjust pump pressure. The set pressure at the ZDB valve takes effect only if it is lower than the setting of the screw-in cartridge valve type DB K.
The unit provides zero-pressure startup and pump circulation capabilities, ensuring low circulation pressure due to its proximity to the pump. Its design minimizes compression volume, resulting in soft switching to depressurized circulation and quick pressure buildup. Users can select from various adjustment types for precise pressure control, including options such as a rotary knob, sleeve with hexagon and protective cap, lockable rotary knob with scale or rotary knob with scale.
For optimal customization, different maximum operating pressures (bar) and maximum flow rates (l/min) are available according to specific requirements. Additionally, its direct flange mounting at the pump contributes to a reduced noise level during operation. This model represents Bosch Rexroth's commitment to delivering robust and precise hydraulic components for complex systems where safety and control are paramount.
$2,839.00 USD
More are expected on April 28, 2025
Status: This product is temporarily out of stock.
Qty: Delivered as early as April 28, 2025 when ordered in
This product is eligible for factory repair.
Zero-pressure start-up and circulation of the pump Intended for direct mounting onto the SAE pressure port of the pump Low circulation pressure due to short distance Low compression volume for soft switching to depressurized circulation Quick pressure build-up 4 adjustment types for pressure adjustment, optionally
• Rotary knob
• Sleeve with hexagon and protective cap
• Lockable rotary knob with scale
• Rotary knob with scale 5 pressure ratings, optional Low noise level due to direct flange mounting at the pump
General
Pump safety blocks type DBAW are pilot-operated pressure relief valves which are integrated into a block and intended to be mounted directly onto SAE pressure ports of pumps.
They are used for limiting and solenoid-actuated unloading (type DBAW) the operating pressure.
Pump safety block type DBAW
In principle, the function of this block corresponds to the function of block type DBA.... Unloading the main control spool, however, is achieved by controlling the mounted directional valve (15). In this case, no cover plate (4) is required.
Pump safety block type DBAW.B…Z… for displacement pumps (with pressure relief valve)
In principle, the function corresponds to type DBAW....
By means of the pressure relief valve type ZDB 6 (16) (data sheet 25751) and actuation of the directional valve (15), the pilot control of the pressure limitation screw-in cartridge valve type DB 20 K is deactivated and the pressure set at the pressure relief valve type ZDB 6 is activated. The pressure adjustment at the pressure relief valve type ZDB 6 only works if it is below the setting of the pressure limitation screw-in cartridge valve type DB 20 K.
Pump safety block type DBAW.B…Z…A for control pump A10V... (with pressure relief valve)
In principle, the function corresponds to type DBAW....
By means of the pressure relief valve type ZDB 6 (16) (data sheet 25751) and by actuation of the directional valve (15), a pressure change is achieved at control port X. The pressure change set at the pressure relief valve type ZDB 6 acts on the controller of the pump. The pressure adjustment at the pressure relief valve type ZDB 6 only works if it is below the setting of the pressure limitation screw-in cartridge valve type DB 20 K.
Pump safety block DBAW.B…ZZ…A for control pump A10V... (with pressure relief valve)
In principle, the function corresponds to type DBAW....
By means of the pressure relief valve type Z(2)DB 6 (16) (data sheet 25751) and by actuation of the directional valve (15), two pressure adjustments are possible at control port X. The pressure adjustment at the pressure relief valve type Z(2)DB 6 only works if it is below the setting of the pressure limitation screw-in cartridge valve type DB 20 K.
01 |
02 |
03 |
04 |
05 |
06 |
07 |
08 |
09 |
10 |
11 |
12 |
13 |
14 |
15 |
16 |
17 |
18 |
19 |
|
DBAW |
2X |
/ |
6E |
K4 |
Type |
|||
01 |
With mounted directional spool valve (data sheet 23178) |
DBAW |
|
Size |
|||
02 |
Size 16 |
15 |
|
Size 25 |
25 |
||
Size 32 |
30 |
||
03 |
With mounted directional spool valve 4WE 6 L37B.6X/..; normally closed |
A |
|
With mounted directional spool valve 4WE 6 H 6X/..; normally open 1) |
B |
||
With mounted directional spool valve 4WE 6 HB 6X/..; normally open 2) |
|||
Type of connection / SAE flange 3) |
|||
04 |
Standard flange (250 … 350 bar) |
F |
|
High-pressure flange (350 bar) |
H |
||
Adjustment type for pressure adjustment 4) |
|||
05 |
Rotary knob |
1 |
|
Sleeve with hexagon and protective cap |
2 |
||
Lockable rotary knob with scale |
3 12) |
||
Rotary knob with scale |
7 |
||
06 |
Without pressure switch |
– |
|
With mounted pressure switch type HED 8 OH… (connector according to DIN EN 175301-803, without mating connector), (data sheet 50061) |
D 5) |
||
Component series |
|||
07 |
Component series 20 ... 29 (20 ... 29: unchanged installation and connection dimensions) |
2X |
|
Pressure rating 6) |
|||
08 |
Set pressure up to 50 bar |
50 |
|
Set pressure up to 100 bar |
100 |
||
Set pressure up to 200 bar |
200 |
||
Set pressure up to 315 bar |
315 |
||
Set pressure up to 350 bar |
350 |
||
09 |
Without additional pressure relief valve (standard, only one pressure limitation) |
no code |
|
With mounted pressure relief valve type ZDB 6 VB…-4X/..SO2 (data sheet 25751) |
Z6) |
||
With mounted pressure relief valve type Z2DB 6 VC…-4X/..SO2 (data sheet 25751) |
ZZ 6) 7) |
||
10 |
Standard version |
no code |
|
Valve for minimum cracking pressure |
U |
||
11 |
Without directional valve |
no code |
|
With directional spool valve |
6E |
||
12 |
Direct voltage 24 V |
G24 |
|
Direct voltage 205 V |
G205 |
||
Alternating voltage 230 V, 50/60 Hz |
W230 |
||
13 |
With concealed manual override (standard) |
N98) |
|
With manual override |
N8) |
||
Without manual override |
no code |
||
Electrical connection 10) |
|||
14 |
Without mating connector; connector DIN EN 175301-803 |
K4 5) |
|
Interface electronics |
|||
15 |
Without electronics |
no code |
|
Nozzle fitting |
|||
16 |
Fixed pumps |
||
Lateral channel closed, transverse channel open, pilot oil bore open; (standard for displacement pumps; pure DB-/DBW function) |
no code |
||
Variable pumps |
|||
Lateral channel closed, transverse channel open, pilot oil bore closed (e.g. for axial piston variable displacement pump type A4VSO140 with DRG controller) |
A00 |
||
Nozzle Ø0.8 mm in lateral channel, transverse channel open; pilot oil bore closed (standard for control pumps with DFR1 or DFLR controller) |
A08 9) |
||
Nozzle Ø1.0 mm in lateral channel, transverse channel open; pilot oil bore closed (for nozzle fitting of the block, refer to the circuit examples) |
A10 9) |
||
Seal material 11) |
|||
17 |
NBR seals |
no code |
|
FKM seals |
V |
||
Type-examination procedure |
|||
18 |
Without type-examination procedure |
no code |
|
Type-examination tested safety valve according to PED 2014/68/EU |
E |
||
19 |
Standard solenoid coil |
no code |
|
Solenoid coil is an approved component with UR-marking according to UL 906 (only version "6E") |
= UR |
1) In versions with pressure relief valve type Z(2)DB | |
2) In versions without pressure relief valve type Z(2)DB | |
3) Observe pressure ratings and connection dimensions! | |
4) Adjustment type for pressure switch type HED8 in brackets! | |
5) Mating connectors, separate order | |
6) Identical pressure rating for pressure limitation screw-in cartridge valve type DB 20 K, pressure relief valve (sandwich plate valve) type Z(2)DB 6 and pressure switch type HED 8 | |
7) Only in case of use for pressure limitation and control of the variable displacement pump type A10VSO | |
8) Notice! Accidental activation of the manual override may lead to uncontrolled machine movements! | |
9) If used on variable displacement pumps with DFLR controllers, the nozzle at port X of the pump control must be removed! | |
10) Externally discharge the pilot oil from the proportional pressure relief valve type DBET(E) | |
11) Observe compatibility of seals with hydraulic fluid used. (Other seals upon request) | |
12) H-key with material no. R900008158 is included in the scope of delivery. |
Notice! Preferred types and standard units are contained in the EPS (standard price list).
general
Size |
16 | 25 | 32 | |||||
Mass |
Pump safety block |
DBAW... |
kg |
6.1 | 6 | 6.1 | 6.7 | |
Type DBAW…Z… |
kg |
7.9 | 7.8 | 7.9 | 8.5 | |||
Type DBAW…ZZ… |
kg |
8.1 | 8 | 8.1 | 8.7 | |||
Pressure switches |
HED 8 |
kg |
0.8 | |||||
Installation position |
any | |||||||
Ambient temperature range |
NBR seals |
°C |
-30 … +50 | - | ||||
FKM seals |
°C |
- | -15 … +50 |
hydraulic
Size |
16 | 25 | 32 | |||
Maximum operating pressure |
Port P |
bar |
350 | |||
Maximum counter pressure |
Port T (DC solenoid) 1) |
bar |
210 | |||
Port T (AC solenoid) |
bar |
160 | ||||
Minimum set pressure |
flow-dependent, see characteristic curves | |||||
Maximum set pressure |
bar |
50 100 200 315 350 |
||||
Maximum flow |
l/min |
300 | 400 | |||
Hydraulic fluid |
see table | |||||
Hydraulic fluid temperature range |
NBR seals |
°C |
-30 … +80 | - | ||
FKM seals |
°C |
- | -20 … +80 | |||
Viscosity range |
mm²/s |
10 … 800 | ||||
Maximum admissible degree of contamination of the hydraulic fluid 2) |
Class 20/18/15 according to ISO 4406 (c) |
1) | 180 bar for version "=UR" |
2) | The cleanliness classes specified for the components must be adhered to in hydraulic systems. Effective filtration prevents faults and simultaneously increases the life cycle of the components. For the selection of the filters, see www.boschrexroth.com/filter. |
Hydraulic fluid |
Classification |
Suitable sealing materials |
Standards |
Data sheet |
|
Mineral oils |
HL, HLP |
NBR, FKM |
DIN 51524 |
90220 |
|
Bio-degradable |
Insoluble in water |
HETG |
NBR, FKM |
ISO 15380 |
90221 |
HEES |
FKM |
||||
Soluble in water |
HEPG |
FKM |
ISO 15380 |
||
Flame-resistant |
Water-free |
HFDU, HFDR |
FKM |
ISO 12922 |
90222 |
Containing water |
HFC (Fuchs Hydrotherm 46M, Petrofer Ultra Safe 620 ) |
NBR |
ISO 12922 |
90223 |
Important information on hydraulic fluids:
For further information and data on the use of other hydraulic fluids, please refer to the data sheets above or contact us. There may be limitations regarding the technical valve data (temperature, pressure range, life cycle, maintenance intervals, etc.). The ignition temperature of the hydraulic fluid used must be 40K higher than the maximum surface temperature.Flame-resistant – containing water:
Maximum pressure differential per control edge 50bar Pressure pre-loading at the tank port >20 % of the pressure differential; otherwise, increased cavitation Life cycle as compared to operation with mineral oil HL, HLP 50 … 100 %Bio-degradable and flame-resistant:
If these hydraulic fluids are used, small amounts of dissolved zinc may get into the hydraulic system.Deviating technical data’: Type-examination tested safety valves type DBA…E, component series 2X according to Pressure Equipment Directive 2014/68/EU
hydraulic
Maximum flow |
See ordering code, safety instructions and characteristic curves "Type-examination tested safety valve" | |
Hydraulic fluid |
Mineral oil (HL, HLP) according to DIN 51524-1 and DIN 51524-2 | |
Hydraulic fluid temperature range |
°C |
-10 … +60 |
Viscosity range |
mm²/s |
12 … 230 |
For applications outside these parameters, please consult us!
(measured with HLP46, ϑOil = 40 ±5 °C)
Inlet pressure dependent on the flow 2)
1) | The characteristic curves apply to an output pressure pT =0 bar in the entire flow range. |
Notice!
The characteristic curves were measured with internal pilot oil return.
Due to the internal pilot oil return, the inlet pressure increases by the output pressure present in port T.
Minimum set pressure and circulation pressure dependent on the flow 1)
Standard version
1) | The characteristic curves apply to an output pressure pT =0 bar in the entire flow range. |
Minimum set pressure and circulation pressure dependent on the flow 1)
Version “U”
1) | The characteristic curves apply to an output pressure pT =0 bar in the entire flow range. |
Safety instructions:Type-examination tested safety valves type DBA…E, component series 2X according to Pressure Equipment Directive 2014/68/EU
Maximum admissible flow q Vmax dependent on the counter pressure pT in the discharge line with internal pilot oil return
Type DBA 15 …-2X/…E
Characteristic curves for intermediate values can be generated by interpolation. Further explanations see below.
pA |
Response pressure in bar |
pT |
Maximum admissible counter pressure in the discharge line in bar (port T) (sum of all possible counter pressures; also see AD2000 data sheet A2) |
pT max |
10 % x pA (with qV = 0) according to PED 2014/68/EU |
qV max |
Maximum admissible flow in l/min |
Explanation of the diagrams (Example: type DBA 15...E): |
|
known: |
Flow of the system/accumulator that has to be secured qVmax = 100 l/min |
Set response pressure of the safety valve pA = 315 bar |
|
unknown: |
pTadmissible |
Solution: |
see arrows in diagram above |
pT admissible (100 l/min; 315 bar) = 15.75 bar |
Type DBA 25 …-2X/…E and type DBA 30 …-2X/…E
pA |
Response pressure in bar |
pT |
Maximum admissible counter pressure in the discharge line in bar (port T) (sum of all possible counter pressures; also see AD2000 data sheet A2) |
pT max |
10 % x pA (with qV = 0) according to PED 2014/68/EU |
qV max |
Maximum admissible flow in l/min |
General circuit example set-up
Arrangement of the nozzles/plugs items 17.1, 17.2 and 17.3
Circuit examples: for displacement pumps (selection)
Type DBAW.B…2X/.Z
Type DBAW.A…2X/…
Type DBAW.B…2X/…
Circuit examples: for variable displacement pump (selection)
Preferably for axial piston variable displacement pumps type A10VSO with DR, DFR1 or DFLR controller 2)
Type DBAW.B…2X/…A08
Type DBAW.B…2X/.Z…A08
Type DBAW.B…2X/.ZZ…A08
2)Notice! | |
If used on variable displacement pumps with DFLR controllers, the nozzle at port X of the pump control must be removed! |
Preferably for axial piston variable displacement pumps type A10VSO with DRG controller
Type DBAW.B…2X/.Z…A00
Type DBAW.B…2X/.ZZ…A00
Dimensions in mm
Required surface quality of the valve contact surface |
1 |
Name plate |
3 |
Port X for variable displacement pump type A10VSO (otherwise closed); G1/4 |
4 |
Port M for pressure gauge; G1/4 |
5 |
Mating connector without circuitry (separate order) |
6 |
Mating connector with circuitry (separate order) |
8 |
Adjustment type "1" 1) |
14 |
Space required to remove the mating connector |
15 |
Seal ring |
16 |
Directional spool valve type WE 6 (data sheet 23178) |
17 |
Dimensions for solenoid with concealed manual override "N9” (standard) – The manual override can only be operated up to approx. 50 bar tank pressure. Avoid damage to the bore of the manual override! (Special tool for the operation, separate order, material no. R900024943). |
18 |
Dimension for valve with manual override "N" |
19 |
Dimension for valve without manual override |
24 |
Hexagon SW30, tightening torque MA = 50 Nm (For tightening, a manual torque wrench with a tolerance ≤ 10 % must be used.) |
25 |
Lock nut SW22, tightening torque MA = 10±5 Nm |
26 |
Porting pattern according to DIN 24340 form A (without locating hole), or ISO 4401-03-02-0-05 (with locating hole for locking pin ISO 8752-3x8-St, material no. R900005694, separate order) |
28 |
Valve mounting bores |
Dimensions in mm
1) | Version "ZZ" |
2) | Version "Z" |
Required surface quality of the valve contact surface |
1 |
Name plate |
3 |
Port X for variable displacement pump type A10VSO (otherwise closed); G1/4 |
4 |
Port M for pressure gauge; G1/4 |
5 |
Mating connector without circuitry (separate order) |
6 |
Mating connector with circuitry (separate order) |
8 |
Adjustment type "1" 1) |
9 |
Adjustment type "2" 1) |
10 |
Adjustment type "3" 1) |
11 |
Adjustment type "7" 1) |
12 |
Hexagon SW10 |
13 |
Space required to remove the key |
14 |
Space required to remove the mating connector |
15 |
Seal ring |
16 |
Directional spool valve type WE 6 (data sheet 23178) |
20 |
Pressure relief valve (sandwich plate) type Z(2)DB 6 …(data sheet 25751) |
24 |
Hexagon SW30, tightening torque MA = 50 Nm (For tightening, a manual torque wrench with a tolerance ≤ 10 % must be used.) |
25 |
Lock nut SW22, tightening torque MA = 10±5 Nm |
26 |
Porting pattern according to DIN 24340 form A (without locating hole), or ISO 4401-03-02-0-05 (with locating hole for locking pin ISO 8752-3x8-St, material no. R900005694, separate order) |
28 |
Valve mounting bores |
Standard flanges type DBA…F… according to DIN ISO 6162-1 |
||||||
Size |
Line connections |
4 valve mounting screws ISO 4762 - 10.9 1) |
Tightening torqueMA in Nm 2) |
|||
P and P1 |
T |
X, M |
Part number |
|||
16 |
SAE 3/4″ |
G3/4 |
G1/4 |
M10 x 95 |
R913015585 |
52 |
25 |
SAE 1″ |
G1 |
G1/4 |
M10 x 95 |
R913015585 |
52 |
32 |
SAE 1 1/4″ |
G1 1/4 |
G1/4 |
M10 x 95 |
R913015585 |
52 |
Admissible pressures (flange connections according to DIN ISO 6121-1) |
|
in bar |
|
SAE 3/4″ |
350 |
SAE 1″ |
315 |
SAE 1 1/4″ |
250 |
High-pressure flanges type DBA…H… according to DIN ISO 6162-2 |
||||||
Size |
Line connections |
4 valve mounting screws ISO 4762 - 10.9 1) |
Tightening torqueMA in Nm 2) |
|||
P and P1 |
T |
X |
Part number |
|||
16 |
SAE 3/4″ |
G3/4 |
G1/4 |
M10 x 95 |
R913015585 |
52 |
25 |
SAE 1″ |
G1 |
G1/4 |
M12 x 105 |
R913000659 |
66 |
32 |
SAE 1 1/4″ |
G1 1/4 |
G1/4 |
M14 x 105 |
R913000660 |
113 |
Admissible pressures (flange connections according to DIN ISO 6121-2) |
|
in bar |
|
SAE 3/4″ |
350 |
SAE 1″ |
350 |
SAE 1 1/4″ |
350 |
1) Valve mounting screws (separate order) | |
4 hexagon socket head cap screws ISO 4762 - 10.9-flZn-240h-L | |
(with friction coefficient μtotal = 0.09 ... 0.14) |
2) Notice!
The tightening torques stated are guidelines when using screws with the specified friction coefficients and when using a manual torque wrench (tolerance ± 10 %).
Standard flanges type DBAW…F…
NG |
B2 |
B7 |
B8 |
H6 |
H7 |
mm |
mm |
mm |
mm |
mm |
|
16 | 12 | 144.5 | 109.5 | 159 | 153 |
25 | 12 | 144.5 | 109.5 | 159 | 153 |
32 | 10 | 144.5 | 111.5 | 159 | 153 |
High-pressure flanges type DBAW…H…
NG |
B2 |
B7 |
B8 |
H6 |
H7 |
mm |
mm |
mm |
mm |
mm |
|
16 | 12 | 144.5 | 109.5 | 159 | 153 |
25 | 12 | 144.5 | 109.5 | 159 | 153 |
32 | 14.5 | 145 | 107 | 163 | 157 |
Standard flanges type DBAW..F…Z…
NG |
B2 |
H8 |
H9 |
mm |
mm |
mm |
|
16 | 12 | 199 | 193 |
25 | 12 | 199 | 193 |
32 | 10 | 199 | 193 |
High-pressure flanges type DBAW..H…Z…
NG |
B2 |
H8 |
H9 |
mm |
mm |
mm |
|
16 | 12 | 199 | 193 |
25 | 12 | 199 | 193 |
32 | 14.5 | 203 | 197 |
Notice!
For reasons of stability, other valve mounting screws must not be used!
Depending on the operating pressure, flange height and thread depth of the pump plate, other screw lengths may be necessary!
At types DBAW.B, the lowest adjustable pressure (circulation pressure) is set at the pressure relief valve in case of power failure or cable break. At type DBAW..A, the pressure limiting function is activated. The unloading function (DBAW) must not be used for safety functions!
Mating connectors for valves with connector “K4”, without circuitry, standard
3P Z4
Mating connectors for valves with connector “K4”, without circuitry, standard
3P Z4
For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector” Mating connectors for valves with one or two solenoids (individual connection)Data sheet
Spare parts & repair
Mating connectors for valves with connector “K4”, with indicator light
3P Z5L
Mating connectors for valves with connector “K4”, with indicator light
3P Z5L
For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector” Mating connectors for valves with one or two solenoids (individual connection)Data sheet
Spare parts & repair
Mating connectors for valves with connector “K4”, with indicator light and Zener diode suppression circuit
3P Z5L1
Mating connectors for valves with connector “K4”, with indicator light and Zener diode suppression circuit
3P Z5L1
For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector” Mating connectors for valves with one or two solenoids (individual connection)Data sheet
Spare parts & repair
Mating connectors for valves with connector “K4”, with rectifier
3P RZ5
Mating connectors for valves with connector “K4”, with rectifier
3P RZ5
For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector” Mating connectors for valves with one or two solenoids (individual connection)Data sheet
Spare parts & repair
Mating connectors for mechanical pressure switches with connector “K14”, without circuitry, standard
4P Z14
Mating connectors for mechanical pressure switches with connector “K14”, without circuitry, standard
4P Z14
For mechanical pressure switches with connector “K14”, according to EN 175301-803 and ISO 4400, 3-pole + PE, “large cubic connector”Data sheet
Spare parts & repair
Mating connectors for mechanical pressure switches with connector “K14”, with indicator lights at connections 2 and 3
4P Z15L
Mating connectors for mechanical pressure switches with connector “K14”, with indicator lights at connections 2 and 3
4P Z15L
For mechanical pressure switches with connector “K14”, according to EN 175301-803 and ISO 4400, 3-pole + PE, “large cubic connector”Data sheet
Spare parts & repair
Ordering code: Type-examination tested safety valves type DBA…E, component series 2X according to Pressure Equipment Directive 2014/68/EU
NG |
Type designation |
Component marking |
Maximum admissible flow qVmax in l/min with pilot oil return |
Set response overpressurep in bar |
16 |
1 2 3 4 5 6 * 7 DBAW 15 ▢▢▢▢2X/▢▢6▢▢E |
TÜV.SV.▢‒1001.14,4.F.G.p |
60 100 150 200 250 |
30 … 60 61 … 110 111 … 210 211 … 315 316 … 350 |
25 |
1 2 3 4 5 6 * 7 DBAW 25 ▢▢▢▢2X/▢▢6▢▢E |
TÜV.SV.▢‒1001.14,4.F.G.p |
70 100 150 200 300 |
30 … 60 61 … 110 111 … 210 211 … 315 316 … 350 |
32 |
1 2 3 4 5 6 * 7 DBAW 30 ▢▢▢▢2X/▢▢6▢▢E |
TÜV.SV.▢‒1001.14,4.F.G.p |
70 100 150 200 300 |
30 … 60 61 … 110 111 … 210 211 … 315 316 … 350 |
1 |
Directional valve, normally closed |
A |
Directional valve, normally open |
B |
|
2 |
Standard flange (250 bar) |
F |
High-pressure flange (350 bar) |
H |
|
3 |
Hand wheel (pressure adjustment sealed, unloading or setting of a lower response pressure possible!) |
1 |
With sealed protective cap (no adjustment/unloading possible) |
2 |
|
4 |
With mounted pressure switch type HED 8 OH… (without mating connector) |
D |
5 |
Pressure in the designation is to be entered by the customer, pressure adjustment ≥ 30 ... 350 bar and possible in 5 bar steps. |
z. B. 150 |
6 |
Without additional pressure relief valve |
no code |
With mounted pressure relief valve type ZDB 6 VB…-4X/..SO2 (data sheet 25751) |
Z |
|
With mounted pressure relief valve type Z2DB 6 VC…-4X/..SO2 (data sheet 25751) |
ZZ |
|
Versions DBAW…Z(Z)E and DBAE(E)…E are only available with ordering code "A00", "A08" or "A10" |
||
* |
Ordering code of the electric data |
z. B. EG24N9K4 |
7 |
NBR seals |
no code |
FKM seals |
V |
|
Value entered at the factory |
Safety instructions: Type-examination tested safety valves type DBA…E, component series 2X according to Pressure Equipment Directive 2014/68/EU
Before ordering a type-examination tested safety valve, it must be observed that for the desired response pressure p , the maximum admissible flow qVmax must be larger than the maximum possible flow of the system to be secured. In this respect, the applicable regulations must be observed! According to PED2014/68/EU the increase of the system pressure by the flow must not be higher than 10 % of the set response pressure (see component marking). The maximum admissible flow q Vmax stated in the component marking (= numerical value instead of the character "G" in the component marking, see ordering code, type-examination tested safety valves) must not be exceeded. Discharge lines of safety valves must end in a risk-free manner. The accumulation of fluids in the discharge lines must not be possible. If a lead seal at the safety valve is removed, the approval according to the PED! The requirements of the Pressure Equipment Directives 2014/68/EU and of data sheet AD2000 A2 must be generally observed! Options DBAE/DBAEE or 2nd/3rd pressure limiting function ( 6 ) are only possible for pressure relief valves for variable displacement pumps (also see ordering code). The unloading function (DBAW) must not be used for safety functions! Possible unloading via the directional valve must not be applied for safety-relevant functions! If unloading is required for safety-relevant functions, an additional safety valve must be installed.It is imperative to observe the application notes!
In the plant, the response pressure specified in the component marking is set at a flow of 11 l/min. The maximum admissible flow stated in the component marking applies for applications without counter pressure in the discharge line (port T).Notice!
The system pressure increases by the counter pressure in the discharge line (port T) with increasing flow (observe AD2000 - data sheet A2 - item 6.3!).
To ensure that this increase in system pressure caused by the flow does not exceed the value of 10% of the set response pressure, the admissible flow has to be reduced dependent on the counter pressure in the discharge line (port T) (see diagrams (Safety instructions, Type-examination tested safety valves).
Related Products
R978855632
$702.00 USD
R978911888
$551.00 USD
R978023351
$567.00 USD
R978864528
$1,009.00 USD
R978016404
$1,461.00 USD