DR6DP2-5X/150Y/12
Manufacturer: Bosch Rexroth
Material #: R900481941
Model : DR6DP2-5X/150Y/12
***Disclaimer: The following summary contains information gathered from various sources such as product descriptions, technical specifications and catalogs. While efforts have been made to provide accurate details, inaccuracies may occur. It is advised to verify all information by contacting Bosch Rexroth directly.***
The Bosch Rexroth DR6DP2-5X/150Y/12 (R900481941) is a direct operated pressure reducing valve designed for way version applications, which means it is capable of limiting the pressure of a secondary circuit. This valve operates by allowing hydraulic fluid to flow freely from channel P to channel A when in the initial position. The secondary pressure can be set via an adjustment type, and the valve maintains this set pressure at a constant level through its control spool mechanism.
The DR6DP2-5X/150Y/12 valve features internal signal and pilot oil routing from channel A through the control line. An increase in pressure within channel A due to external forces causes further movement against the compression spring, leading to a connection between channel A and tank channel TY. This allows for discharge of excess hydraulic fluid into the tank, preventing undue pressure increase.
Leakage oil from the spring chamber is discharged externally through channel TY. Additionally, an optional check valve can be installed for free flow back from channel A to channel P. Monitoring of secondary pressure is facilitated by a pressure gauge connection.
This model is designed for subplate mounting with porting patterns that conform to DIN form A and an ISO pattern with locating hole available as an option. It offers various adjustment types including rotary knob, threaded pin with hexagon and protective cap, lockable rotary knob with scale, and rotary knob with scale. The DR6DP2-5X/150Y/12 comes in size component series X and can handle a maximum operating pressure of up to 315 bars with a maximum flow rate capacity specified by its design parameters.
$702.00 USD
More are expected on May 30, 2025
Status: This product is temporarily out of stock.
Qty: Delivered as early as May 30, 2025 when ordered in
This product is eligible for factory repair.
The valve type DR 6 DP is a direct operated pressure reducing valve in 3-way version, i. e. with pressure limitation of the secondary circuit.
It is used to limit a system pressure. The secondary pressure is set via the adjustment type (4)
The valve is open in initial position. Hydraulic fluid can flow from channel P to channel A without restrictions. The pressure in channel A is simultaneously applied via the control line (6) at the piston area opposite the compression spring (3). If the pressure in channel A exceeds the value set at the compression spring (3), the control spool (2) moves to control position and keeps the set pressure in channel A at a constant level.
Signal and pilot oil come internally via the control line (6) from channel A.
If the pressure in channel A increases further due to an external force effect at the actuator, it pushes the control spool (2) even further against the compression spring (3).
In this way, channel A is connected to channel T(Y) via the control edge (8) at the control spool (2). So much hydraulic fluid is discharged into the tank that the pressure can only increase slightly.
The leakage oil discharge from the spring chamber (7) is always effected externally via channel T(Y).
For the free flow back from channel A to channel P, a check valve (5) can optionally be installed.
A pressure gauge connection (1) allows for the control of the secondary pressure.
Type DR 6 DP1-5X/.Y…
(measured with HLP46, ϑOil = 40 ±5 °C)
pA-qV characteristic curves
pA-qV characteristic curves
Notice!
The curve development is maintained if the pressure is set lower according to the pressure rating.
The characteristic curves apply to the pressure at the valve output p = 0 bar across the entire flow range.
Δp-qV characteristic curves
Δp-qV characteristic curves
|
1 |
P to A (minimum pressure differential) |
|
2 |
A to T(Y) (minimum pressure differential) |
|
3 |
Δp only via check valve |
|
4 |
Δp via check valve and fully opened control cross-section |
Version "M"
Without check valve
Version "no code"
With check valve
Dimensions in mm
Dimensions in mm
|
1 |
Name plate |
|
2 |
Adjustment type "1" |
|
3 |
Adjustment type "2" |
|
4 |
Adjustment type "3" |
|
5 |
Adjustment type "7" |
|
6 |
Space required to remove the key |
|
7 |
Valve mounting bores |
|
8 |
Lock nut SW24 |
|
9 |
Hexagon SW10 |
|
10 |
Identical seal rings for ports A, B, P, T (Y) |
|
11 |
Pressure gauge connection G1/4; 12 mm deep; internal hexagon SW6 |
|
12 |
Without check valve |
|
13 |
With check valve |
|
14 |
Port B without function |
|
15 |
Porting pattern according toISO 4401-03-02-0-05 (with locating hole for locking pin ISO 8752-3x8-St, material no. R900005694, separate order) |
Subplates (separate order)
(without locating hole)
G 341/01 (G1/4)
G 342/01 (G3/8)
G 502/01 (G1/2)
(with locating hole)
G 341/60 (G1/4)
G 342/60 (G3/8)
G 502/60 (G1/2)
Valve mounting screws (separate order)
4 metric hexagon socket head cap screws
ISO 4762 - M5 x 50 - 10.9-flZn-240h-L
at friction coefficient μtotal = 0.09 to 0.14,
tightening torque MA = 7 Nm] ± 10% ,
material no. R913000064
4 hexagon socket head cap screws UNC
10-24 UNC x 2” (on request)
Related Products
R900927505
$1,270.00 USD
R900592281
$930.00 USD
R901382320
$1,127.00 USD
R900547109
$994.00 USD
R900491533
$825.00 USD
