4WP6EA6X/5
Manufacturer: Bosch Rexroth
Material #: R978008177
Model : 4WP6EA6X/5
***Disclaimer: The following summary contains information gathered from various sources such as product descriptions, technical specifications and catalogs. While efforts have been made to provide accurate details, inaccuracies may occur. It is advised to verify all information by contacting Bosch Rexroth directly.***
The Bosch Rexroth 4WP6EA6X/5 (R978008177) is a high-performance directional spool valve designed for controlling the start, stop, and direction of fluid flow within hydraulic systems. This valve is part of the WP series and features a robust housing, pneumatic actuation cylinder, control spool, and return springs. The radial positioning of the ports for control ensures efficient fluid dynamics within the system.
When in a deenergized state, the control spool is maintained in either a central or initial position by the return springs. The spool can be shifted to the desired position using the actuation elements. For applications that may experience flows exceeding the valve's performance limit during switching processes, a throttle insert can be utilized in channel P to regulate flow rates effectively.
The 4WP6EA6X/5 model is direct operated with pneumatic actuation and does not include spring return but comes with a detent feature allowing each spool position to be securely locked. This particular configuration ensures that there are no defined spool positions when deenergized if no detent or return springs are used.
Designed for versatility in application, this valve follows porting patterns according to DIN without a locating hole and ISO with one, ensuring compatibility with various international standards. Subplates necessary for installation are available but must be ordered separately. Additionally, this model can be equipped with inductive position switches and proximity sensors for contactless detection of spool position.
With its component series X designation, this Bosch Rexroth directional valve can withstand maximum operating pressures up to several hundred bar and is capable of handling significant flow rates measured in liters per minute. The specific details regarding maximum operating pressure and flow should be referenced from Bosch Rexroth datasheets for precise specifications. This valve's reliability and adaptability make it suitable for a wide range of applications requiring precise hydraulic flow management.
$617.00 USD
More are expected on September 30, 2024
Status: This product is temporarily out of stock.
Qty: Delivered as early as September 30, 2024 when ordered in
This product is eligible for factory repair.
General information
Valves of type WP are fluidically actuated directional spool valves. They control the start, stop and direction of a flow.
The directional valves basically consist of housing (1), one or two actuation elements (2) (pneumatic actuation cylinder), control spool (3) and one or two return springs (4). The ports for the control are positioned radially (5).
When de-energized, the control spool (3) is held in the central position or in the initial position by the return springs (4) (except impulse spool).
The control spool (3) is moved to the desired spool position by means of the actuation elements.
Throttle insert
The use of a throttle insert is required when due to prevailing operating conditions, flows can occur during the switching processes, which exceed the performance limit of the valve.
It is inserted in channel P of the directional valve.
Type 4WP 6 E6X/...
Without spring return, with detent,
version ..OF/..
Directional valves with pneumatic actuation are also available as a 2-spool position valve with detent (7). If actuation elements with detent are used, each spool position can be locked.
Without spring return,
version ..O/..
If actuation elements without return springs and without detent are used, there is no defined spool position in the de-energized state.
Type 4WP 6 C6X/OF/N...
general
|
Size |
6 | ||
|
Weight (approx.) |
Valve with one actuation cylinder |
kg |
1.8 |
|
Valve with two actuation cylinders |
kg |
2 | |
|
Installation position 1) |
any | ||
|
Ambient temperature range |
NBR seals |
°C |
-30 … +80 |
|
FKM seals |
°C |
-20 … +80 | |
| 1) | With version ../O.. (A, C and D) : horizontal |
hydraulic
|
Size |
6 | ||
|
Maximum operating pressure |
Port P |
bar |
315 |
|
Port A |
bar |
315 | |
|
Port B |
bar |
315 | |
|
Port T 1) |
bar |
160 | |
|
Maximum flow |
l/min |
60 | |
|
Flow cross-section (spool position 0) |
Symbol Q |
mm2 |
approx. 6 % of nominal cross-section |
|
Symbol W |
mm2 |
approx. 3 % of nominal cross-section | |
|
Minimum pilot pressure 2) |
bar |
4 | |
|
Maximum pilot pressure |
bar |
10 | |
|
Pilot volume |
cm³ |
4.24 | |
|
Hydraulic fluid |
see table | ||
|
Hydraulic fluid temperature range |
NBR seals |
°C |
-30 … +80 |
|
FKM seals |
°C |
-20 … +80 | |
|
Viscosity range |
mm²/s |
2.8 … 500 | |
|
Maximum admissible degree of contamination of the hydraulic fluid 3) |
Class 20/18/15 according to ISO 4406 (c) | ||
|
Maximum switching frequency |
Hz |
2 | |
| 1) | With symbols A and B, port T must be used as leakage oil connection if the operating pressure exceeds the admissible tank pressure. |
| 2) | See characteristic curves |
| 3) | The cleanliness classes specified for the components must be adhered to in hydraulic systems. Effective filtration prevents faults and simultaneously increases the life cycle of the components. For the selection of the filters, see www.boschrexroth.com/filter. |
|
Hydraulic fluid |
Classification |
Suitable sealing materials |
Standards |
|
|
Mineral oil |
HL, HLP |
FKM, NBR |
DIN 51524 |
|
|
Bio-degradable |
Insoluble in water |
HEES (synthetic esters) |
FKM |
VDMA 24568 |
|
HETG (rape seed oil) |
FKM, NBR |
|||
|
Soluble in water |
HEPG (polyglycols) |
FKM |
VDMA 24568 |
|
|
Other hydraulic fluids on request |
||||
Inductive position switch type QM: electrical connection
The electric connection is realized via a 4-pole mating connector (separate order) with connection thread M12 x 1.
For applications outside these parameters, please consult us!
electrical
|
Connection voltage (DC voltage) |
V |
24 | ||
|
Voltage tolerance (connection voltage) |
+30 %/-15 % | |||
|
Admissible residual ripple |
% |
≤ 10 | ||
|
Max. load capacity |
mA |
400 | ||
|
Switching outputs 
|
PNP transistor outputs, load between switching outputs and GND | |||
|
Pinout 
|
1 |
V |
24 | |
|
2, 4 |
Switching output |
mA |
400 | |
|
3 |
Earthing (GND) |
V |
0 | |
(measured with HLP46, ϑOil = 40 ±5 °C)
Δp-qV characteristic curves
|
Symbol |
Direction of flow |
|||
|
P-A |
P-B |
A-T |
B-T |
|
|
A |
3 |
3 |
– |
– |
|
B |
3 |
3 |
– |
– |
|
C |
1 |
1 |
3 |
1 |
|
D |
5 |
5 |
3 |
3 |
|
E |
3 |
3 |
1 |
1 |
|
F |
1 |
3 |
1 |
1 |
|
G |
6 |
6 |
9 |
9 |
|
H |
2 |
4 |
2 |
2 |
|
J |
1 |
1 |
2 |
1 |
|
L |
3 |
3 |
4 |
9 |
|
M |
2 |
4 |
3 |
3 |
|
P |
3 |
1 |
1 |
1 |
|
Q |
1 |
1 |
2 |
1 |
|
R |
5 |
5 |
4 |
– |
|
T |
10 |
10 |
9 |
9 |
|
U |
3 |
3 |
9 |
4 |
|
V |
1 |
2 |
1 |
1 |
|
W |
1 |
1 |
2 |
2 |
|
Y |
5 |
5 |
3 |
3 |
|
Further characteristic curves: |
|
|
7 |
Symbol “R” in switching position “b” (B → A) |
|
8 |
Symbol “G” and “T” in central position (P → T) |
|
9 |
Symbol “H” in central position (P → T) |
Minimum pilot pressure dependent on the tank pressure
At a higher tank pressure, the minimum pilot pressure has to be increased according to this diagram.
Performance limits
(measured with HLP46, ϑOil = 40 ±5 °C)
Notice!
The switching function of the valves is independent from the filtration due to the adhesive effect. To achieve the specified admissible flow values, a full flow filtration with 25 μm is recommended. The flow forces acting within the valves also influence the flow performance.
With 4-way directional valves, the specified flow data are therefore valid for normal operation with 2 directions of flow (e. g. from P to A and simultaneous return flow from B to T).
If there is only one direction of flow, the admissible flow may be significantly lower in critical cases (e. g. if a 4-way directional valve is used as a 3-way directional valve due to blocked port A or B).
|
Characteristic curve |
Symbol |
|
1 |
A, B |
|
2 |
A/O, C, C/O, D, D/O, E, E1-, G, H, J, L, M, Q, U, W, und Y |
|
3 |
F, P |
|
4 |
R |
|
5 |
T |
|
6 |
V |
| 1) |
Example: – Symbol E with spool position "a" → ordering code ..EA.. – Symbol E with spool position “b” → ordering code ..EB.. |
| 2) | Symbol E1-: P → A/B pre-opening |
Attention!
Caution in conjunction with differential cylinders due to pressure intensification!
|
Ordering code |
Type of actuation |
||
|
Symbol |
Actuation side |
Spool return |
|
|
A, C, D |
|
||
|
../O.. |
|
||
|
../OF.. |
|
||
|
B, Y |
|
||
|
E, F G, H J, L M, P Q, R T, U V, W |
a = A |
|
|
|
b = B |
|
||
|
|||
Dimensions in mm
|
|
Required surface quality of the valve contact surface |
|
1 |
Valve with 2 spool positions and 2 actuation cylinders |
|
Valve with 3 spool positions and 2 actuation cylinders |
|
|
2 |
Actuation cylinder “a” |
|
3 |
Actuation cylinder “b” |
|
4 |
Plug screw for valve with 1 actuation cylinder (2 spool positions) |
|
5 |
Optional auxiliary operating device |
|
6 |
Same seal rings for ports A, B, P, T |
|
7 |
Name plate |
|
8 |
Porting pattern according toISO 4401-03-02-0-05 (with locating hole for locking pin ISO 8752-3x8-St, material no. R900005694, separate order) |
|
9 |
Connection |
|
10 |
Port with version “WPZ” |
|
11 |
Alternative clamping length (): 22 mm |
Subplates according to data sheet 45052 (separate order)
(without locating hole)
G 341/01 (G1/4)
G 342/01 (G3/8)
G 502/01 (G1/2)
(with locating hole)
G 341/60 (G1/4)
G 342/60 (G3/8)
G 502/60 (G1/2)
G 341/12 (SAE-6)1)
G 342/12 (SAE-8)1)
G 502/12 (SAE-10)1)
1) On request
Valve mounting screws (separate order)
Clamping length 42 mm:4 hexagon socket head cap screws, metric
ISO 4762-M5 x 50-10.9-flZn-240h-L
(friction coefficient μtotal = 0.09 to 0.14);
tightening torque MA = 7 Nm ± 10 %,
material no. R913000064
or
4 hexagon socket head cap screws
ISO 4762-M5 x 50-10.9 (self procurement)
(friction coefficient μtotal = 0.12 to 0.17);
tightening torque MA = 8.1 Nm ± 10 %
4 hexagon socket head cap screws UNC
10-24 UNC x 2″ ASTM-A574
(friction coefficient μtotal = 0.19 to 0.24);
tightening torque MA = 11 Nm± 15 %,
(friction coefficient μtotal = 0.12 to 0.17);
tightening torque MA = 8 Nm ± 10 %,
material no. R978800693
Clamping length 22 mm:4 hexagon socket head cap screws, metric
ISO 4762-M5 x 30-10.9-flZn-240h-L
(friction coefficient μtotal= 0.09 to 0.14);
tightening torque MA = 7 Nm ± 10 %,
material no. R913000316
or
4 hexagon socket head cap screws
ISO 4762-M5 x 30-10.9 (self procurement)
(friction coefficient μtotal = 0.12 to 0.17);
tightening torque MA = 8.1 Nm± 10 %
4 hexagon socket head cap screws UNC
10-24 UNC x 1 1/4 ″
(friction coefficient μtotal = 0.19 to 0.24);
tightening torque MA = 11 Nm± 15 %,
(friction coefficient μtotal = 0.12 to 0.17);
tightening torque MA = 8 Nm± 10 %,
material no. R978802879
Spool position monitoring
Inductive position switch type QM
Dimensions in mm
| 1) | For dimensions, see valve dimensions |
Notice:
The dimensions are nominal dimensions which are subject to tolerances.
Related Products
R901437709
$1,297.00 USD
R900938912
$1,891.00 USD
R900959159
$1,298.00 USD
R900565953
$860.00 USD
R978891956
$1,406.00 USD
