Please ensure Javascript is enabled for purposes of website accessibility

PRESSURE AND FLOW CONTROL SYSTEM

SYDFEE-2X

Material #: R901468198

Model : SYDFEE-2X/140R-PSD62KC5-0000-A0A1VXX-025

Price: $16,378.00

A SYDFEE-2X control system is used for the electro-hydraulic control of swivel angle, pressure and power (partially optional, see type key pilot control and preload valve and ordering code) of an axial piston variable displacement pump.
The control system consists of the following components: Axial piston variable displacement pump A10VSO.../31 VT-DFPE-.2X proportional valve as pilot valve with integrated electronics including inductive position transducer for valve position sensing. Position transducer for sensing the swivel angle Pressure transducer with suitable signal level and dynamics (optionally HM 20, otherwise separate order) Preload valve with integrated pressure relief function SYDZ (optional)

Buy Now

$16,378.00

Status: This product is temporarily out of stock. 

We have you covered! Place your order today! More are expected on September 4, 2023  

A SYDFEE-2X control system is used for the electro-hydraulic control of swivel angle, pressure and power (partially optional, see type key pilot control and preload valve and ordering code) of an axial piston variable displacement pump.
The control system consists of the following components: Axial piston variable displacement pump A10VSO.../31 VT-DFPE-.2X proportional valve as pilot valve with integrated electronics including inductive position transducer for valve position sensing. Position transducer for sensing the swivel angle Pressure transducer with suitable signal level and dynamics (optionally HM 20, otherwise separate order) Preload valve with integrated pressure relief function SYDZ (optional)

1

Swash plate

2

Pilot valve

3

Counter piston

4

Actuating piston

5

Spring

6

Inductive position transducer for valve position

7

Swivel angle position sensor

8

Proportional solenoid

11

Integral electronics

12

Connector X1

13

Connector X2 for connection of the HM 20 pressure transducer cable version (only with actual pressure value input F)

14

Mating connector X3 for connection of the CAN bus (only available with SYDFEC/SYDFEn)

15

Drive shaft

16

Connection flange

17

Subplate, optionally with through-drive

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

SYDFEE-2X

/

P

12

*

Pump of the SYDFE control system

Series

01

Control system with internal analog electronics

SYDFEE-2X

Pump combinations (see order example)

SY2DFE.-2X,
SY3DFE.-2X

Size

018

028

045

071

100

140

02

Displacement cm³

18

28

45

71

100

140

Direction of rotation looking at the drive shaft

03

Right

R

Left

L

Hydraulic fluid

04

Mineral oil according to DIN 51524 (HL/HLP)

P

Drive shaft variant

05

Cylindrical with fitting key DIN 6885 (not in connection with through-drive)

Ø18

Ø22

Ø25

Ø32

Ø40

Ø45

P

Splined shaft profile SAE J 744

1)

3/4"

1 1/2"

1 3/4"

S

Splined shaft profile SAE J 744 (higher torque)

7/8"

1"

1 1/4"

R

Connection flange (centering in mm)

Ø18

Ø22

Ø25

Ø32

Ø40

Ø45

06

ISO 2-hole

80

100

100

125

125

A

ISO 4-hole

180

B

SAE 2-hole

82,55

101,6

101,6

127

127

C

SAE 4-hole

152,4

D

Port for working lines pressure port B and suction port S

07

SAE, laterally opposite, mounting thread metric

12

Through-drive (All through-drives with single pumps come without a hub and are operationally safe, provided with an end cover)

08

Without through-drive

N00

Centering

Attachment pump (examples)

2)​

ISO Ø100 mm

A10VSO..31 NG28/45

KD3

ISO Ø125 mm

A10VSO..31 NG71/100

KD5

ISO Ø180 mm

A10VSO..31 NG140

KD7

SAE Ø82.55 mm

A10VSO..31 NG18, PGF2, PGH2, PGH3, AZPF

KC1

SAE Ø101.6 mm

PGH4, 1PF2G3, PGF3

KC3

SAE Ø127 mm

PGH5

KC5

SAE Ø152.4 mm

A10VO140

KC6

Base pump variant

09

Standard (internal pilot oil)

0000

External supply

0479

External supply + regenerative operation

0487

Pilot and preload valve of the SYDFEE control system

Spool design

10

Standard (NG28 ... NG140)

A

4-groove spool (NG18)

C

Integrated electronics, installation orientation, see note on feature 11

11

Radially to the pump axis

0

folded 90° in the direction of the subplate

2

Control, additional function

A

B

C

D

12

Switchable pressure controller (high signal)

A

Power limitation adjustable at the OBE valve

B

Power limitation adjustable via analog input

C

Pressure controller that can be switched off (high signal)

D

Electronics assembly, option

13

Standard electronics with leakage oil compensation

0

Standard electronics without leakage oil compensation

1

Actual pressure value input
(For the description of the connectors refer to electrical connection)

Plug-in connector

C

4...20 mA

V

0...10 V

E

1...10 V

F

0,5...5 V

14

Current input 4...20 mA

X1

C

Voltage input 0...10 V

X1

V

Voltage input 1...10 V

X1

E

Voltage input 0.5...5 V

X2

F

Pressure transducer

15

HM 20-2X/315-F-C13-0,5, measurement range 315 bar (0.5...5 V) with connection cable 0.5 m for direct connection to X2 (only in connection with actual pressure value input F)

L

Without pressure transducer

X

Preload valve with integrated pressure limitation

16

Pressure limitation 200 bar (tolerance ± 8 bar)

1

Pressure limitation 250 bar (tolerance ± 10 bar)

2

Pressure limitation 300 bar (tolerance ± 12 bar)

3

Without preload valve

X

17

Further details in the plain text e. g. SO variant

*

1) ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5.
2) Also observe the conditions for the attachment pumps.

Note on feature 11: Valve, installation orientation of the integrated electronics

Clockwise direction of rotation, installation orientation 0

Clockwise direction of rotation, installation orientation 2

Counterclockwise direction of rotation, installation orientation 0

Counterclockwise direction of rotation, installation orientation 2

available

-

not available

Ordering code pump combination SYHDFEE-2X

01

02

03

04

05

SY2HDFEE-2X

/

/

+

01

2-fold pump

SY2HDFEE-2X

02

Size of the main pump

1)

03

Size of the attachment pump or pump abbreviation if the attachment pump is not SYHDFE (e.g. PGF)

1)

04

Material number without "R9" for the main pump or type designation if material number is not known

05

Material number without "R9" for the attachment pump or type designation if material number is not known

1) Detailed information see type key

01

02

03

04

SY3HDFEE-2X

/

+

+

01

3-fold pump

SY3HDFEE-2X

02

Material number without "R9" for the main pump or type designation if material number is not known

03

Material number without "R9" for the attachment pump or type designation if material number is not known

04

Material number without "R9" for the attachment pump or type designation if material number is not known

Example of name plate of a pump combination

For enquiries regarding the control system, material number, production order number, serial number, and date of production are necessary.

mechanic and hydraulic

Size

18 28 45 71 100 140

Displacement

Vg max

cm³

18 28 45 71 100 140

Speed 1)

maximum at Vg max

nnom

rpm

3300 3000 2600 2200 2000 1800

maximum at Vg < Vg max

nmax zul

rpm

3900 3600 3100 2600 2400 2100

Minimum speed

nmin

rpm

50

Max. flow (displacement)

at nnom and Vg max

qV max

l/min

59.4 84 117 156 200 252

with nE = 1500 rpm and Vg max

qvE max

l/min

27 42 68 107 150 210

Max. power (Δp = 280 bar)

at nnom and Vg max

P max

kW

27.7 39 55 73 93 118

with nE = 1500 rpm and Vg max

PE max

kW

12.6 20 32 50 70 98

Max. torque (Δp = 280 bar)

Tmax

Nm

80.1 125 200 316 445 623

Maximum permissible drive torque

Fitting key

Ttotal

Nm

88 137 200 439 857 1206

Splined shaft S overall torque

Ttotal

Nm

124 - 1104 1620

Max. admissible through-drive torque

TD

Nm

108 - 778 1266

Splined shaft R overall torque

Ttotal

Nm

- 225 400 644 -

Max. admissible through-drive torque

TD

Nm

- 176 365 548 -

Drive shaft load

max. admissible axial force

Fax max

N

700 1000 1500 2400 4000 4800

max. admissible radial force

Fq

N 2)

350 1200 1500 1900 2300 2800

Mass

Pump without through-drive incl. pilot valve

m

kg

14 17 23 35 47 62

in addition, preload valve

m

kg

3.3 6.3

in addition, in case of external supply

m

kg

2

Moment of inertia around drive axis

kg·m²

0.0009 0.0017 0.0033 0.0083 0.0167 0.0242

Filling quantity of the housing

l

0.4 0.7 1 1.6 2.2 3

Maximum admissible operating pressure

pmax

bar

280 3) 280

Operating pressure, min. (without load)

with preload valve

pmin

bar

≥ 1

without preload valve

pmin

bar

≥ 20

in case of external supply (20 bar) 4)

pmin

bar

> 10

Admissible inlet pressure

p

bar

0.8 ... 10

Hydraulic fluid

Mineral oil (HL, HLP) to DIN 51524

Hydraulic fluid temperature range

ϑ

°C

-20 … +70

Maximum admissible degree of contamination of the hydraulic fluid according to ISO 4406

Class 18/16/13 (for particle size ≤ 4/6/14 μm)
1) The values are applicable at an absolute pressure of 1 bar at the suction opening S. With a reduction of the displacement or an increase in the inlet pressure, the speed can be increased according to the following characteristic curve. With a reduced inlet pressure, the speed is to be reduced.
2) In case of higher radial forces, please consult us
3) In case of higher pressures, please consult us
4) In continuous operation; in case of operation below 10 bar, observe the notes

elektrisch

Size

18 28 45 71 100 140

Operating voltage

UB

24 +40 % –5 %

Operating range (short-time operation)

Upper limit value

UB(t)max

V

35

Lower limit value

UB(t)min

V

21

Current consumption (in static control operation)

Rated current

Inom

A

0.6

Maximum current

Imax

A

1.25

Inputs

Actual pressure value input X1;
pin 10 and 11

U or I

Determination by means of ordering code

Analog current inputs, load 1)

RB

100 Ω

Analog voltage inputs

RE

≥ 50 kΩ

Digital inputs

Logic 0

≤ 0,6 V

Logic 1

≥ 21 V

Outputs

pactual / UOUT1

UO

0 ... 10 V

Imax

1,5 mA

αactual / UOUT2

UO

± 10 V

Imax

1,5 mA

Digital outputs

Logic 0

Ua < 1 V

Logic 1

Ua ≥ UB – 5 V; 10 mA (short-circuit-proof)

Ambient temperature range at the pump

ϑ

°C

​0 … ​60

Storage temperature range (pump + electronics)

ϑ

°C

​0 … ​70

Electronics design

Integrated in the pilot valve (OBE)

Type of protection according to EN 60529

Pump incl. pilot valve

IP65 with mounted and locked plug-in connectors
1) With configuration on current input: Maximum admissible input current 30 mA
2) With SYDFEC, SYDFEn and SYDFED, the outputs are parameterizable, for the condition as supplied, see electrical connection.

Notice:

For information on the environment simulation testing for the areas of EMC (electro-magnetic compatibility), climate and mechanical load, see data sheet 30030-U.

 

Control loop quality

Notes:

The specified values are only valid when using the system-related components specified in this data sheet. At pressures < 20 bar, higher tolerances have to be anticipated due to lower actuating forces.

Swivel angle control

Pressure control

1)

Linearity tolerance

≤ 1.0 %

≤ 1.5 % (≤ 1.0 %)

Temperature error

≤ 0.5 % / 10 K

≤ 0.5 % / 10 K

Hysteresis

≤ 0.2 %

≤ 0.2 %

Repetition accuracy

≤ 0.2 %

≤ 0.2 %

1) Without considering the pump pulsation.

For applications outside these parameters, please consult us!

Transition function with pressure command value step with spool design "A"

The specified curve shapes and control times refer to a drive speed of 1500 rpm and are only reached with an optimization of the pressure controller.

T 95% in ms with a connected hydraulic fluid volume (lines and actuators)

Hydraulic fluid volume in l

T95% in ms

<​ 5

150

5 ... 10

200

15 ... 15

250

Transition function with swivel angle command value step with spool design "A"

Size 18, 28, 45, 71 p = 20 bar

Size 18, 28, 45, 71 p = 50 bar

Size 100 p = 50 bar

Size 140 p = 50 bar

For pressures up to 40 bar, the values of the response times are greater.

Schematic diagram: Actuating system supplied internally

1) When using the pressure transducer HM 20 cable version:
Installation in P (pump) or MP1 (preload valve) in connection with electronic version "Actual pressure value input F".
When using an external pressure transducer:
Installation in the P1 line (preferably close to the actuator) and electrical connection via the central connector.
When using a preload valve, the pressure transducer is to be connected to P1 or MP1.

Schematic diagram: Actuating system supplied externally

The representation shows an example with integrated electronics.

1) The use of an anti-cavitation valve (check valve with 0.2 bar spring) is essential in order to prevent dry-running in the error case.

2)

Pressure transducer

Mounting options

Comment

HM 20-2X/315-F-C13-0.5 (cable version)

P

Only in connection with actual pressure value input "F"

HM 20-2X/...-.-K35 (connector version)

P1

Preferably close to the actuator

3) Maximum pressure limitation must be provided by the customer!
4) Observe upper limit for external pilot oil pressure! (see operating instructions), recommendation: 20 bar absolute.

Important notes on external supply:

In the case of an actuating system with external supply, the pump adjustment will - in case of voltage failure - not switch to zero stroke but to the negative stop (displacement of 100 % flow from the system to the tank). With an active fault message, it is imperative that the machine control reacts (e. g. switching off the drive motor of the pump, interrupting the external supply of the actuating system). The command values for pressure and flow must always be greater than zero (pcommand ≥ 3 bar, αcommand ≥ 5 %) as due to drift or tolerances, there is no exact "zero" pressure or "zero" swivel angle. Under unfavorable conditions, smaller command value presettings can lead to cavitation. The actual pressure value must not be less than 10 bar for more than 10 minutes (lubrication).

 

Allocation of connector or mating connector and cable set

Pin

Signal

Description

Signal direction

Type of signal

Allocation in the cable set (accessories)

1

+ UB

Voltage supply

IN

24 V DC

1

Supply line 3 x 1.0 mm2

2

0 V = L0

Reference potential for the voltage supply

2

PE

Earth

Earthing connection for the electronics

green/yellow

3

Fault

Signals faults, e.g. cable break command / actual values, controller monitoring (logic 0 = error)

OUT

logic 24 V

white

Supply line 10 x 0.14 mm2 shielded (one end of the shield must be connected to the control!)

4

M0

Reference potential for analog signals

yellow

5

αCommand

Swivel angle command value

IN

analog ±10 V

green

6

αActual

Actual swivel angle value, normalized

OUT

analog ±10 V

Violet

7

pCommand

Pressure command value

IN

analog 0...10 V

pink

8

pActual

Actual pressure value, normalized

OUT

analog 0...10 V

1)​

red

9

Function dependent on electronic type and additional function, see table Functions at pin 9

brown

10

Actual pressure value H

Actual pressure value input: Signal level dependent on feature 14 of the ordering codes Reserved with type "F" (0.5...5 V)

IN

analog

black

11

Actual pressure value L

analog

blue

n.c.

gray

Functions at pin 9

Pin

Additional function

Function dependent on feature 12 of the ordering codes (see page type key pilot and preload valve)

Signal direction

Type of signal

9

-..A…

Selecting a different oil volume adjustment (switch TD)

IN

logic 24 V

-..B…

Power limitation active

OUT

logic 24 V

-..C…

Command value of power limitation

IN

analog 0...10 V

-..D…

Switch off pressure controller

IN

logic 24 V

1) When using a pressure transducer with raised zero point (e. g. 4 ... 20 mA), a voltage of –1 ... –2.5 V will be output in case of a cable break.

X2: Connection of pressure transducer HM 20

      HM 20-2X/315-F-C13-0,5 (cable version) (mating connector M12)

Pin

Signal HM 20

Pin

1

OUT, +UB

2

n.c.

3

Reference L0

4

IN, analog, 0.5 to 5 V DC

5

n.c.

installation orientation 0

The unit dimensions of the base pump (axial piston variable displacement pump A10VSO.../31) are contained in data sheet 92711.

Size 18 … 140

(Valve mounting direction "0"; shaft design "S”; without through-drive “N00”)
Dimensions in mm

(representation size 100)

Size

Dimensions with base pump variant "0479" or "0487"

Max. length

A1

A3 1)

A4

A5

A6

A6 I

A6 II

A8 I

A8 II

A8 III

A9

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

18 120 198 158 63 178 63 115 233 125 100 170
28 128 208 158 63 195 80 115 243 135 115 194
45 134 218 158 63 205 90 115 253 145 125 219
71 146 232 158 63 254 104 150 267 159 150 257
100 151 237 158 63 247 100 147 272 164 150 317
140 162 250 143 78 257 110 147 285 182 150 317
1) Dimension with base pump “0000” design

installation orientation 2

Size 18 … 140

(Valve mounting direction "2"; shaft design "S”; without through-drive “N00”)
Dimensions in mm

(representation size 100)

Size

Dimensions with base pump variant "0479" or "0487"

Max. length

A1

A3

A4

A5

A6

A6 I

A6 II

A8 I

A8 II

A8 III

A9

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

18 100 116 158 63 178 63 115 151 125 100 253
28 108 127 158 63 195 80 115 162 135 115 263
45 114 137 158 63 205 90 115 172 145 125 278
71 126 151 158 63 254 104 150 186 159 150 306
100 131 156 158 63 247 100 147 191 164 150 373
140 142 180 143 78 257 110 147 215 182 150 373

Combination pumps

Attachment pump

Main pump

A10VSO 18

A10VSO 28

A10VSO 45

A10VSO 71

A10VSO 100

A10VSO 140

A1

A2

A3

A4

A1

A2

A3

A4

A1

A2

A3

A4

A1

A2

A3

A4

A1

A2

A3

A4

A1

A2

A3

A4

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

A10VSO 18

164

204

349

399

164

204

349

399

184

229

374

424

217

267

412

462

275

338

483

533

275

350

495

554

A10VSO 28

164

204

368.5

410

184

229

393.5

435

217

267

431.5

473

275

338

502.5

544

275

350

514

556

A10VSO 45

184

229

413

453

217

267

451

491

275

338

522

562

275

350

534

574

A10VSO 71

217

267

484

524

275

338

555

595

275

350

567

609

A10VSO 100

275

338

613

664

275

350

625

679

A10VSO 140

275

350

625

688

Ports

Size

18

28

45

71

100

140

B:

Working line (SAE J518)

1)

Size

3/4"

3/4"

1"

1"

1 1/4"

1 1/4"

Mounting thread (DIN 13)

M10 x 1.5; 17 deep

M14 x 2; 19 deep

Maximum pressure

2)

bar

350

S:

Suction line (SAE J518)

1)

Size

1"

1 1/4"

1 1/2"

2"

2 1/2"

2 1/2"

Mounting thread (DIN 13)

M10 x 1.5; 17 deep

M12 x 1.75; 20 deep

M12 x 1.75; 17 deep

Maximum pressure

2)

bar

10

1) Dimensions according to SAE J518 only, metric mounting thread deviating from the standard.
2) Application-specific short-time pressure peaks may occur. Please observe when selecting measuring devices and fittings. Specified pressures are in bar absolute.

Notes regarding size 71:

With pressure connection “B” of size 71, two SAE mounting connections rotated by 90° are available. SAE 1 1/4″ standard pressure series, 207 bar , for pressures up to 250 bar or SAE 1″ standard pressure series, 344 bar, for pressures up to 350 bar. For operating pressures exceeding 250 bar, the pressure flange SAE 1” must be used.

Dimensions in mm

Hubs for through-drives

Hubs for the combination of single pumps or the combination of SYDFE with other pumps. Observe that the attachment pump has a splined shaft SAE J744 with the specified diameter.

The following conditions apply to the attachment pumps listed in the table:

SYDFE and A10VSO with shaft S or R Internal gear pump PGH with shaft R, flange U2, see data sheet 10223 Internal gear pump PGF3 with shaft J, flange U2, see data sheet 10213 External gear pump AZPF with shaft R, front cover R, see data sheet 10089

Observe that the through-drive of the main pump and the flange of the attachment pump (see type key pump) are identical. Check in the current data sheet of the gear pump whether the shaft ends have the specified dimensions.

Main pump SYDFE or A10VSO...

Attachment pump

Size 18

Size 28

Size 45

Size 71

Size 100

Size 140

Ø shaft

Pump type (examples)

R902436099

R902436199

R902436100

R902436200

R902436201

R902436202

3/4" 19-4

(SAE A-B)

SYDFE-2X, A10VSO..31
Size 018 shaft S

R902436098

R902436084

R902436083

R902436101

R902436102

7/8" 22-4

(SAE B)

SYDFE-2X, A10VSO..31
Size 028 shaft R; PGF3

R902436103

R902436104

R902436105

R902436204

1" 25-4

(SAE B-B)

SYDFE-2X, A10VSO..31
Size 045 shaft R; PGH4

R902436085

R902436105

R902436106

1 1/4" 32-4

(SAE C)

SYDFE-2X, A10VSO..31
Size 071 shaft R

R902436086

R910943555

1 1/2" 38-4

(SAE C-C)

SYDFE-2X, A10VSO..31
Size 100 shaft S; PGH5

R910943565

R910932172

1 3/4" 44-4

(SAE D)

SYDFE-2X, A10VSO..31
Size 140 shaft S

R910943528

R910986299

R910943529

R91094345

R910943560

R910943551

5/8" 16-4

(SAE A)

1PF2G2, PGF2,

PGH2, PGH3, AZPF

Through-drives

KD3

 

Flange ISO 100, 2-hole for the attachment of

SYDFE.-2X (size 28 and size 45, flange A) A10VSO..31 (size 28 and size 45, flange A, see data sheet 92711)

Sectional presentation with examples for hubs (order number for hubs see hubs for through-drives)
Dimensions in mm

Size

A1

A2

A3

A4

A5

A6

mm

mm

mm

mm

mm

28 204 41.7 17.8 - - M12; 15 right through
45 229 41.7 17.9 46.7 18.4 M12; 14 right through
71 267 44.1 20.3 49.1 20.8 M12; 20 deep
100 338 41 17.6 45.9 18.2 M12; 20 deep
140 350 41.1 18 45.9 18.3 M12; 20 deep

KD5

 

Flange ISO 125, 2-hole for the attachment of

SYDFE.-2X (size 71 and size 100, flange A) A10VSO..31 (size 71 and size 100, flange A, see data sheet 92711)

Sectional presentation with examples for hubs (order number for hubs see hubs for through-drives)
Dimensions in mm

Size

A1

A2

A3

A4

A5

A6

mm

mm

mm

mm

mm

71 267 58.6 21.8 - - M16; 20 right through
100 338 56.4 19.5 63.9 7.9 M16; 20 deep
140 350 55.4 17.4 73.3 7.9 M16; 20 deep

KD7

Flange ISO 180, 4-hole for the attachment of

SYDFE.-2X (NG140, flange B) A10VSO..31 (NG140, flange B, see data sheet 92711)

Sectional presentation with examples for hubs (order number for hubs see hubs for through-drives)
Dimensions in mm

Size

A1

A2

A3

A5

mm

mm

mm

140 350 75 8 M16; 22 right through

KC1

 

Flange SAE 82-2 (SAE A, 2-hole) for the attachment of

SYDFE.-2X (size 18, flange C) A10VSO..31 (size 18, flange C, see data sheet 92711) PGF2 (shaft J, flange U2, see data sheet 10213) PGH2 and PGH3 (shaft R, flange U2, see data sheet 10223) AZPF (shaft R, front cover R, see data sheet 10089)

Sectional presentation with examples for hubs (order number for hubs see hubs for through-drives)
Dimensions in mm

Size

A1

A2

A3

A4

mm

mm

mm

18 182 40 43 M10; 14.5 deep
28 204 39 47 M10; 16 deep
45 229 40.5 53 M10; 16 deep
71 267 40 61 M10; 20 deep
100 338 40 65 M10; 20 deep
140 350 41 77 M10; 17 deep

KC3

 

Flange SAE 101-2 (SAE B, 2-hole) for the attachment of

SYDFE.-2X (size 28 and size 45, flange C) A10VO..31 (size 28 and size 45, flange C, see data sheet 92701) PGF3 (shaft J, flange U2, see data sheet 10213) PGH4 (shaft R, flange U2, see data sheet 10223)

Sectional presentation with examples for hubs (order number for hubs see hubs for through-drives)
Dimensions in mm

Size

A1

A2

A3

A4

A5

A6

A7

mm

mm

mm

mm

mm

mm

28 204 43 16.5 47 - - M12; 15 deep
45 229 42 16.5 53 18.4 46.7 M12; 18 deep
71 267 43 16.5 61 20.8 49.1 M12; 20 deep
100 338 41 16.5 65 10.5 65 M12; 20 deep
140 350 44 16.5 77 18.3 45.9 M12; 20 deep

KC5

 

Flange SAE 127-2 (SAE C, 2-hole) for the attachment of

SYDFE.-2X (size 71 and size 100, flange C) A10VO..31 (size 71 and size 100, flange C, see data sheet 92701) PGH5 (shaft R, flange U2, see data sheet 10223)

Sectional presentation with examples for hubs (order number for hubs see hubs for through-drives)
Dimensions in mm

Size

A1

A2

A3

A4

A5

A6

A7

mm

mm

mm

mm

mm

mm

71 267 55.5 17.9 61 - - M16; 18 deep
100 338 57 17.9 65 8 65 M16; 25 deep
140 350 60 17.9 77 9 77.3 M16; 32 deep

KC6

 

Flange SAE 152-4 (SAE D, 4-hole) for the attachment of

SYDFE.-2X (size 140, flange D) A10VO..31 (size 140, flange D, see data sheet 92701)

Sectional presentation with examples for hubs (order number for hubs see hubs for through-drives)
Dimensions in mm

Size

A1

A3

A4

A5

mm

mm

mm

140 350 10.5 77 M16; 24 deep

Project planning information

Always shield command and actual value cables. The distance to aerial lines or radios must be at least 1 m. Do not lay signal lines close to power lines. For amending notes on the SYDFE control system, see the operating instructions (see section "More information about this control system").

Torsionally flexible couplings for attachment to a standard electric motor

Motor

SYDFE.-2X

Frame size/characteristic

Shaft diameter

NG18

Shaft S, 3/4”

NG28

Shaft S or R, 7/8″

NG45

Shaft S or R, 1″

100/0

112/0

28

R901038012

R901038017

132/0

38

R900704699

R901012344

R900772898

160/0

42

R900726977

R900991864

R900994283

180/0

48

R900032918

R900062159

200/0

55

R901038026

R901038025

225/0

60

R900750847

R901066409

250/0

65

R900988348

Motor

SYDFE.-2X

Frame size/characteristic

Shaft diameter

NG71

Shaft S or R, 1 1/4"

NG100

Shaft S, 1 1/2"

NG140

Shaft S, 1 3/4"

160/0

42

R900228413

180/0

48

R900240468

R900242567

200/0

55

R901038021

R901104689

R901038048

225/0

60

R900228375

R901050508

R900988121

250/0

65

R900986404

R901046864

R900708084

280/0

75

R900218487

R901055216

R901052451

315/0

80

R9010468941)

R9010468301)

315/1

80

R901046885

1) Up to 40 °C

Accessories

Version 12/2014, enquire availability

Accessories

Material number

Data sheet

Mating connector 12-pole for central connection X1 without cable (assembly kit)

R900884671

08006

Mating connector 12-pole for central connection X1 with cable set 2 x 5 m

R900032356

Mating connector 12-pole for central connection X1 with cable set 2 x 20 m

R900860399

Pressure transducer HM 20-2X, measurement range 315 bar (4 ... 20 mA)

R901342029

30272

Pressure transducer HM 20-2X, measurement range 315 bar (0.1 ... 10 V)

R901342030

30272

Test device VT-PDFE-1-1X/V0/0

R900757051

29689-B

Compact power supply unit VT-NE32-1X

R90080049

29929

More accessories

Accessories for through-drives

See Accessories

Torsionally flexible couplings for attachment to a standard electric motor

See Accessories

Mating connectors for valves with round connector, 11-pole + PE

12P N11

Mating connectors for valves with round connector, 11-pole + PE

12P N11

For valves with round connector according to EN 175201-804, 11-pole + PE

Data sheet

Spare parts & repair

Mating connectors for valves with round connector, 11-pole + PE, shielded, with assembled connection line

12P N11 +

Mating connectors for valves with round connector, 11-pole + PE, shielded, with assembled connection line

12P N11 +

For valves with round connector according to EN 175201-804, 11-pole + PE

Data sheet

Spare parts & repair